Search

Permanent Magnet Screw Air Compressor Serial TPM

Origin: TYPHOON - EU

Code: TPM

Model: TPM

PM Motor Typhoon TPM Seres . Inverter Screw Compressor
- Power: 5.5 - 132 KW (7.5 - 175 HP)
- Working pressure: 4.5 - 15.0 Kg/cm2
- Flow: 0.7 - 23.5 m3/min
- Drive: Feed shaft
- Cooling by wind / by water
- Working temperature: 0 - 45 oC
- Voltage: 380V/3phase/50Hz
- Boot method: Soft VSD, PID..
- Noise level: low
- Using PLC control system (Program Logic Controller) for starting modes, setting gas pressure, working mode and safety mode for the machine, All controlled and displayed on the fine screen liquid form (LCD). Can monitor the device remotely via PC, Laptop, Smast Phone.

Product Information
Comment

Permanent magnet variable speed screw air compressor, with synchronous motor, has no slip, no electrical excitation and low heat loss.

Product Advantages

Permanent magnet motor

The motor IP54 and the main engine share the same shaft, without coupling, central bracket, belt, gear, etc. The transmission efficiency is 100%, whose efficiency is 5-12% higher than that of the same capacity asynchronous motor. The motor is bearingless and oil sealed, eliminating routine maintenance and repairation. The volume is half smaller than the main component of ordinary three phase motor, and the weight is one-third lighter than that of the common motor host component.

Frequency inverter

Frequency conversion operation, start smoothly and stably with low noise. The large reduction of the starting current reduces the maximum power load, so as to save a lot of electricity. The demand of compressed air is varied every time depend on loading condition and the fluctuation rate is 40 - 80%. With application of Inverter Control system, the compressed air can be produced accurately according to the demand. And eventually, it can make much energy saving compared to normal compressor.

Intelligent control

Through higher intelligent control, the size of air production can be adjusted automatically, therefore, no matter how the air volume fluctuates, the pressure is always maintained which means the operation is really under constant pressure. The motor responds quickly, starts quickly and loads quickly.When the air volume is suddenly changed, it can respond quickly and the reaction time is within 50ms. It completely avoids the damage of uers' equipment and product defects caused by the pressure tuation, moreover, it reduces the energy loss caused by the pressure fluctuation.

Energy Saving Airend

Energy Saving Airend (using 6 SKF bearings)
With new and exclusive design of Typhoon screw rotor which has been passed through the accurate machining procedure and test, it improves efficiency of airend and optimizes the airflow. We use a set of opposite biconical roller bearings at the end of exhaust end enable to support thrust load effectively and extend the running time.

Energy Saving Intake Valve

Intake valve have function of proportional adjusting the air inflow, according to user's air demand, intake volume can be adjusted from 0-100%.
With non-return function,
With air-bleeding function,
With no-load delay function

High capability cooling system

Using axial fan, large propeller, lower speed and lower noise. With high air pressure, high air volume and stable operation.
Large heat exchanger, using high strength aluminum alloy material, ensure good cooling effect even under 45 degree environment.

Product Parameter

TPM SERIES TECHNICAL SPECIFICATION
Model	Power		Pressure	Capacity	Dimensions	Weight	Outlet Pipe	Noise Level
Model	KW	HP	bar	M3/min	(LxWxH) mm	Kg	Diameter	dB
TPM7.5A	5.5	7.5	7	0.90	840x670x925	200	G3/4	65
			8	0.80
			10	0.70
			13	0.60
TPM10A	7.5	10	7	1.05	840x670x925	200	G3/4	65
			8	1.10
			10	1.00
			13	0.80
TPM15A	11	15	7	1.68	1000x820x1145	300	G3/4	65
			8	1.60
			10	1.45
			13	1.30
TPM20A	15	20	7	2.50	1000x820x1145	300	G3/4	65
			8	2.30
			10	2.00
			13	1.74
			15	1.50
TPM30A	22	30	7	3.52	1100x880x1190	390	Gl 1/4	75
			8	3.36
			10	3.06
			13	2.80
			15	2.20
TPM40A	30	40	7	5.20	1200x950x1358	530	Gl 1/4	75
			8	4.72
			10	4.30
			13	3.90
TPM50A	37	50	7	6.51	1300x1000x1366	590	Gl 1/2	75
			8	6.19
			10	5.62
			13	5.10
TPM60A	45	60	7	7.71	1300x1000x1366	590	Gl 1/2	80
			8	7.35
			10	6.67
			13	5.80
TPM75A	55	75	7	10.14	1600x1300x1600	1210	G2	80
			8	9.66
			10	8.77
			13	7.95
TPM100A	75	100	7	13.50	1600x1300x1600	1210	G2	80
			8	12.51
			10	11.21
			13	9.78
TPM120A	90	120	7	14.91	1600x1300x1600	1220	G2	85
			8	14.17
			10	12.88
			13	11.50
TPM150A	110	150	7	20.96	2090x1550x2000	2300	DN65	85
			8	20.06
			10	17.02
			13	15.30
TPM175A	132	>175	7	23.37	2090x1550x2000	2300	DN65	85
			8	22.50
			10	21.03
			13	18.00

The exhaust volume is measured under the rated exhaust pressure, according to the national standard GB3853 test (equivalent to ISO1217 appendix C).
Recommend frquency 30%-100%.
The above data is based on the standard grid- 380V/ 50HZ.
Please make further inquiry for the non-standard specification type and machines which are used under high/low temperature, high humidity, dusty working environment.